SimpleBot Initial Software Configuration

The Simple Bot software is installed on the Raspberry Pi. If you are attending the workshop you will be provided with a pre-installed SD card to use. This page will help you with any additional configuration that is required and allow you to create your own SD image if you need to later.

Changing the default configuration

1. Insert the Micro SD card into a laptop or workstation using the provided adaptor
2. When the image is mounted open the file `machine.local` in a text editor
3. Edit the file as explained by the comments in the file.
4. Save the file and unmount the SD card and then remove it
5. Insert the card into the Raspberry Pi and power up

By default the Miniconf image will use a hostname based on the unique serial number of the ARM CPU.

Creating your own SD image

You can create a suitable development kit as follows:

1. Install a Raspberry Pi Raspian Image on your SD by following these instructions.
2. Boot your raspberry Pi and login as user `pi` with password `raspberry`
3. Make sure your keyboard is correctly configured and you have internet access
4. Run the following command
    bash <(wget https://   #todo)

General references

Compiling the driver for the RT7601 WiFi chipset

This worked:

### Prepare kernel source
sudo su
cd /usr/src
git clone --depth 1 https://github.com/raspberrypi/linux.git #downloads about 132MB
ln -s /usr/src/linux /lib/modules/`uname -r`/build
cd /lib/modules/`uname -r`/build
make mrproper
gzip -dc /proc/config.gz > .config
make modules_prepare
wget https://github.com/raspberrypi/firmware/raw/master/extra/Module.symvers
exit
### Fetch driver source
cd ~
mkdir wireless-drivers
cd wireless-drivers
wget https://dl.dropboxusercontent.com/u/11876059/DPO_MT7601U_LinuxSTA_3.0.0.4_20130913.tar.gz
tar zxf DPO_MT7601U_LinuxSTA_3.0.0.4_20130913.tar.gz
cd DPO_MT7601U_LinuxSTA_3.0.0.4_20130913
### Make and install driver
make
sudo make install
sudo reboot

To configure it as a wireless client, edit /etc/network/interfaces and add this to the end:

auto ra0
allow-hotplug ra0
iface ra0 inet dhcp
wpa-ssid "YOUR SSID"
wpa-psk "YOUR PASSWORD"

Note that some of the steps below (kernel source setup, etc) may also be necessary. I need to redo this from scratch on a clean system to verify.

http://www.maketecheasier.com/set-up-raspberry-pi-as-wireless-access-point/

Other notes from various attempts:

http://elinux.org/RPi_USB_Wi-Fi_Adapters

http://va3paw.com/2014/03/16/hsmm-mesh-on-raspberry-pi/

This "fixnet" script may be useful to re-establish the network connection if it drops out after a day or so: http://www.raspberrypi.org/forums/viewtopic.php?f=28&t=40474#p330868

Download driver source from http://www.mediatek.com/en/downloads/mt7610u-usb/

sudo su
apt-get update
apt-get upgrade
rpi-update
cd /usr/src
git clone --depth 1 https://github.com/raspberrypi/linux.git
ln -s /usr/src/linux /lib/modules/`uname -r`/build
cd /lib/modules/`uname -r`/build
make mrproper
gzip -dc /proc/config.gz > .config
make modules_prepare
wget https://github.com/raspberrypi/firmware/raw/master/extra/Module.symvers
exit
cd ~/mt7610u_wifi_sta_v3002_dpo_20130916
make
make install

cd ~/wireless-drivers/DPO_RT5572_LinuxSTA_2.6.1.3_20121022
sudo make
sudo make install

git clone https://github.com/jamesfoley/raspberry-pi-MT7601